Home About us Contact us News Check e-mail
   
English   Espanol   Chinese
 

.
Container candle making machine

Container Shape , This kind machine is suitable for the Round or Square Container shape.

1. A brief of the candle making machine
My moulding machines are specially designed for making candles of various forms.
2. Structure and Performance of common candle making machine
2.1 Structure
The machine is composed of candle holding dish, water tank, machine frame, spool box, hand wheel, spindle, bevel gear, lead screw, nut, nut shelf, bearing box, cross beam, push-off tube and candle moulding tubes, etc.

2.2 Performance
2.2.1 Water tank, candle moulding tube enable the fluid wax to solidify by means of circulating water in the tube.
2.2.2 Candle holding dish make usre that the wick is in the center of the tube and the candle to be properly placed and clamped.
2.2.3 Lead heads and push-off tubes are used for the forming of the candle tip and the push of the candle from the candle moulding tube.
2.2.4 The spool box is used for mounting the wick spool.

3. Installation and Test run
The machine is a movable design and need no fixed foundation just place the machine smooth and steady.
Check carefully if any spare parts are turning loose or tends to fall off, and clean the accumulated dirt on all parts of the machine. Fill oil on all lubrication points. Candle moulding tubes shall be smeared with small amount of lubricant or white Vaseline oil. Raise and lower the cross beam of the unloaded machine several times, if it's very flexible to be started and in normal operation, then do the followings:
3.1 If there is clearance between the lead head and the candle mould cavity, expanding the punch can be used to strike the lead head lightly, so that the fitting between the lead head and the candle mould will be closed sealed to prevent any leakage of wax liquid.

3.2 Threading with candle wick. When threading with candle wick on a candle moulding machine of 240 piece capacity, attention shall be paid to the treading method. Since there are 8 rows of candle moulding tubes on water tank, and there are 10 rows of spool in the spool will be too far from the hole on the cover of the spool box, and this may result in a mess of the threading. Therefore, grouping method must be adopted. Threading starts from both ends and advances to the middle part, only by this means can threading be prevent from getting into a mess.
3.3 Swing the crank handle to lower the cross beam to the stopping position.

4. Operation Process
4.1 Rotate the hand wheel to making cross beam fall to the lower stopping position. Place the candle holding-dish in the slot on the locating plate, pull the locating plate to the front stopping point. Hang the wick in the serrate slot of the candle-holding plate. When the wax liquid half solids, cut off the wick, remove the candle-holding, dump the residual wax liquid. When the wax liquid in the candle moulding tube completely solidifies, rotate the hand wheel, through movement of the bevel gear, lead screw, nut and nut shelf, move the cross rail and push the candle off tube. Put on the candle-holding dish to store the candle. Let the wick enter the serrated hole, rotate the hand wheel to lower the cross beam to the lower stopping position.

5. Packing and transportation
The machine shall be covered with a plastic film to prevent entrance of water. It shall be enclosed by wooden box combined with iron nails. The box shall be reinforced by iron wires at the two ends to prevent damages in transportation. The box shall not be turned upside-down and shall avoid clashes.


 
   
   
   
 
Hand mould for the ball
   
 
setup your own candle factory How to setup the Factory


Setup the Candle Production Line

TroubleShooting

make the regular candle Candle Making Machine (pouring)

Common shape
Spiral shape
Taper shape
Pillar shape
7 Days & 7 Nights
Birthday shape
T-light Shape
Votive Shape
Floater Shape
Container Shape
Special Shape
More

Melt the solid wax Wax Treat Equipment

Melt the solid into liquid, then supply it to the candle making machine or the paraffin powder spraying machine.
Wax Melting Machine

Instant Melting Box

Adjusting Color Pot

 

Produce your candle by more moden machine Automatic Candle Making Machine

The equipment to make the T-light shape candle, votive shape cadle, pillar shape candle by express, automatic one. Needs the paraffin powder as the raw material.
Auto. Candle Extruder

Tealight Candle Reeling & Pressing Machine

Filling Line

 

Chalk & Crayon Making Machine Chalk & Crayon Making Machine

The equipment to make chalk or crayon.
Chalk Making Machine

Crayon Making Machine

 

 

Material and additives for the candle and chalk making
Materials



Wax
Wick
T-light Cup and Tab
Stearic Acid (stearine)
Citronella Oil
Colors & Pigment
Scents
Special wick for T-light, votive and 7 Days & 7 Nights

Gypsum (for Chalk)

 

Relavent Equipment


T-Light Cup Machine

Water Cooling System

Wick Dipping Machine

Wick Cutting Machine

Candle Packing

Candle Packaging Machine (household)

Tealight Candle Packaging

 

Paraffin Powder Manufacturing

Paraffin Powder Spraying Machine

Paraffin Powder Milling Drum

Super Powder House

 

 

 

LOGIN

members only

Complete Production Line

Complete Tealight Candle Pressing Line

Complete Tealight Filling Line

Automatic Birthday Candle Production Line

Make Candle by Hand


Teach you how to make candle

Vivid Candles

Make Candle with mould

 

Guan Candle Making Machine Co.,Ltd.
We are the manufacturer of the candle, crayon and chalk making machine.

Zhongqing Street, Dalian, China 116013
FAX: +86-411-8236 3077

E-mail: vcan@vip.163.com xuguan@hotmail.com

Server in Asia
Server in America
Tope MaquinaPartner in China
Latin America
All content copyright 1997-2019 The Guan Candle Making Machine Co.,Ltd.
All Rights Reserved.

China Candle!